---
title: TITAN Command User Guide
description: "Everything you need to install TITAN Command safely: what’s in the box, mounting, power, network connections and what the status light is telling you."
url: "https://www.dejero.com/faq/titan-command-user-guide/"
updated: "2026-11-20"
category: TITAN User Guides
---

# TITAN Command User Guide

Model CommandM3E4 · Document UG-150-001, revision 001 · December 2025

 [Product brief (PDF)](/wp-content/uploads/2025/11/TITAN-Command.pdf)

TITAN Command blends three 5G modems with any wired or wireless IP link — satellite, fibre, Wi-Fi — into one connection using Dejero Smart Blending Technology. Its cellular and Wi-Fi antennas are built in, so installation is mostly SIMs, power and cables. It is managed remotely in Dejero Control, supports VPN tunneling, and is FirstNet Capable™ and Verizon Frontline Verified.

In a hurry? The [TITAN Command Quick Start](/faq/titan-command-quick-start-guide/) covers setup in six steps.

[Dejero TITAN Command](https://player.vimeo.com/video/1151230703?dnt=1)

Watch: TITAN Command overview. Step-by-step training videos are coming soon.

## From box to online in six steps

1. [Insert SIM cards](#insert-sim-cards)
2. [Mount the device](#mount-the-device)
3. [Connect GPS](#plan-placement-and-gps)
4. [Connect power (DC or PoE++)](#power-it)
5. [Connect WAN and LAN](#connect-wan-and-lan)
6. [Check the status light](#what-the-status-light-means)

## What’s in the box

- TITAN Command device
- DC power input connector
- DIO connector
- Mounting bracket
- 6 × M4 × 6 mm screws
- QR code for the Quick Start Guide

**You’ll also need:** nano SIM cards (industrial-grade recommended), 4 × M6 screws to fix the bracket, and an external GPS/GNSS antenna if you need location data. Optional accessories: AC/DC power supply, IP67 enclosure, IP54 case.

## Before you start

**Safety essentials:** the antennas are inside the device, so keep at least 20 cm (8 in) between TITAN Command and anyone nearby. Power it off near fuel, chemicals, blasting sites and medical equipment. Only authorized Dejero personnel may open or service it; opening it voids the warranty.

- Operate between −40 °C and +70 °C with 0.6 m/s airflow (0 °C to +40 °C on the optional AC/DC adapter). Keep it out of direct sun.
- Keep it dry, and handle it with care — drops can loosen internal components.
- Cellular data is billed monthly per unit. Large video transfers can exceed your allocation.

 Full safety and regulatory notes

**Class A device.** Complies with FCC Part 15 Class A and ICES-003 Class A. Intended for commercial environments; use in residential areas may cause interference.

**RF exposure.** Meets FCC and ISED exposure limits when 20 cm separation is maintained.

**ISED.** LE-LAN devices in the 5150–5250 MHz band are restricted to indoor use, including inside trains.

**Medical and hearing devices.** The modems may interfere with pacemakers, implanted defibrillators, hearing aids and cochlear implants.

**Electrical.** Disconnect all power before servicing. Keep the outlet near the equipment and easily accessible; maintain protective earth. Not suitable where children are likely to be present.

**Battery.** Risk of explosion if the CMOS battery is replaced with an incorrect type.

## Ports and indicators

![TITAN Command front panel with callouts A to E](https://www.dejero.com/wp-content/uploads/2025/12/Command-Connections-and-Ports-Front-QSG.png)

![TITAN Command back panel with callouts A to D](https://www.dejero.com/wp-content/uploads/2025/12/Command-Connections-and-Ports-Back-QSG.png)

| Side | Port | What it does |
| --- | --- | --- |
| Front | A · DC power + IGN | 3-pin terminal block, 8–36 VDC, optional ignition input |
| Front | B · 4 × RJ-45 2.5 GbE | Ports 1–3 WAN; Port 4 LAN and PoE++ power input |
| Front | C · USB-C | Monitor, keyboard and mouse for the local interface |
| Front | D · Power button | On, off and reboot |
| Front | E · LEDs | L1 status, L2 reserved, Power |
| Back | A · SIM cover | Three nano SIM slots |
| Back | B · Serial (COM) | Serial connection |
| Back | C · DIO | 10-pin digital I/O, including GPS ADR inputs |
| Back | D · GPS antenna | SMA; antenna not included |

 DIO port pinout (10 pins)

| Pin | Function |
| --- | --- |
| 1 | Wheel tick input (GPS ADR mode) |
| 2, 7 | Ground |
| 3, 4, 5 | General digital input |
| 6 | Direction input (GPS ADR mode) |
| 8, 9, 10 | General digital output |

Inputs accept 8–36 VDC; outputs are open-drain. In an IP67 enclosure with M12 connectors, the DIO range is limited to 8–30 V. Fit ferrules to every wire, then press the orange plunger with a small flat-blade screwdriver to insert or release it.

## What the status light means

The L1 light on the front matches the device status in Dejero Control. The Power light is green when the unit has power; L2 is reserved for future use.

| L1 light | Status in Control | What it means and what to do |
| --- | --- | --- |
| Off | INITIALIZING | Not yet connected to Control. Wait a few minutes; if it stays off, check power. |
| Blinking green | CONNECTING | Trying to reach Control. Check that at least one SIM or WAN link has internet access. |
| Solid green | CONNECTED | Connected and operational. No action needed. |
| Blinking red | DISCONNECTED | Connected but having an issue reaching the concentrator. Contact Dejero Support. |
| Solid red | ERROR | Connected but not operational. Contact Dejero Support. |

## Plan placement and GPS

With the antennas built in, where you put the device decides your signal. Place it where cellular reception is strongest — near the outside of a building or vehicle if needed — with room behind it for the GPS cable.

- Screw the GPS antenna to the SMA port on the back. Tighten the RF cable’s SMA connector, not the hex lock nut on the chassis.
- Avoid sharp bends or crimps in the GPS cable. Active and passive antennas are both supported.
- For untethered dead reckoning (UDR), keep the GPS antenna close to the device. For automotive dead reckoning (ADR), place both near the wheel supplying speed pulses.

## Insert SIM cards

Skip this if your unit came with Dejero data services pre-installed.

1. Power off the device.
2. Remove the SIM cover on the back. Its end doubles as the insertion tool.
3. Insert up to three nano SIM cards. Industrial-grade SIMs keep working across the full temperature range.
4. Reattach the cover, then reconnect power.

## Mount the device

![Underside of TITAN Command showing the mounting bracket](https://www.dejero.com/wp-content/uploads/2025/12/Command-Bracket-QSG.png)

1. Align the mounting bracket on the bottom of the device with the installation location.
2. Attach the bracket to the device with the six supplied M4 × 6 mm screws.
3. Fix the bracket to the surface with four M6 screws through the keyhole openings.
4. Tighten all screws.

## Power it

### Option 1: DC power (8–36 V)

1. Insert the wires into the power connector: Pin 1 (left) V+, Pin 2 (middle) GND, Pin 3 (right) IGN, optional. Tighten the clamping screws. Wire colours vary — confirm before powering.
2. In vehicles, fuse V+ at 10 A from the battery and IGN at 1 A.
3. Plug the connector into port A on the front and tighten its screws without overtightening.
4. Connect the power cable to the power source.

Wire IGN only if a vehicle ignition or remote switch should turn TITAN Command on and off.

### Option 2: PoE++ on Port 4

Connect a PoE++ Ethernet cable to Port 4. The device powers up automatically, and Port 4 stays your LAN port while it carries power.

## Connect WAN and LAN

- **WAN — Ports 1, 2 and 3:** extra internet links for the blend, such as wired Ethernet, a satellite modem or a Wi-Fi bridge. Each needs public internet access, and the firewall must allow outbound TCP/UDP and their stateful responses.
- **LAN — Port 4:** your computer, switch or wireless access point.
- Label each cable WAN or LAN. TITAN Command can also act as a Wi-Fi hotspot; a router on the LAN port is separate from that built-in Wi-Fi.
- To use the local interface on a monitor, connect a monitor, keyboard and mouse to USB-C via an adapter. Reboot if the unit was already running.

## Power on, off and reboot

| To | Do this |
| --- | --- |
| Power on or off | Hold the power button at least 2 seconds |
| Reboot | Hold the power button at least 10 seconds |
| With IGN wired | On 5 seconds after ignition; off 30 minutes after ignition off (defaults) |

TITAN Command starts automatically when power is applied. Watch the [L1 status light](#what-the-status-light-means) to confirm it reaches Control.

## Configure in Dejero Control

1. Go to [control.dejero.com](https://control.dejero.com). You need administrator permissions and the login details Dejero emailed you.
2. Enter your email address and password, then select **Sign in**.
3. Configure the device remotely.

## Technical specifications

| Model | CommandM3E4 |
| --- | --- |
| Cellular | 3 × 5G with LTE/3G fallback; integrated antennas |
| Ethernet | 4 × RJ-45 2.5 GbE |
| Wi-Fi | 802.11 a/b/g/n/ac/ax hotspot |
| SIMs | 3 × nano SIM; industrial (extended-temperature) recommended |
| GPS | 1 × SMA for external antenna; UDR and ADR dead reckoning |
| Power | 8–36 V, 3-pin terminal block, or PoE++ on Port 4 |
| Consumption | 22 W idle · 40 W typical · 60 W peak |
| Dimensions (H × W × D) | 6.0 × 32.8 × 25.7 cm (2.36 × 12.91 × 10.12 in) |
| Weight | 2.6 kg (5.73 lb) |
| Operating temperature | −40 °C to 70 °C with 0.6 m/s airflow; 0 °C to 40 °C with optional AC/DC adapter |
| Storage temperature | −40 °C to 70 °C |
| Humidity | About 95% at 40 °C, non-condensing |
| Shock and vibration | MIL-STD-810G Methods 514.6 and 516.6 — 40 G operating, 75 G crash hazard |
| Compute | Intel Atom® x7433RE (3.4 GHz max turbo), 8 GB RAM, 128 GB storage |

 Supported cellular bands

**5G:** n1, n2, n3, n5, n7, n8, n12, n13, n14, n18, n20, n25, n26, n28, n29, n30, n38, n40, n41 (PC1.5, PC2), n48, n66, n71, n75, n76, n77 (PC1.5, PC2), n78 (PC1.5, PC2), n79 (PC1.5, PC2)

**LTE:** B1, B2, B3, B4, B5, B7, B8, B12, B13, B14, B17, B18, B19, B20, B25, B26, B28, B29 (DL), B30, B32 (DL), B34, B38, B39, B40, B41 (PC2), B42, B43, B46 (LAA), B48 (CBRS), B66, B71

**3G:** B1, B2, B4, B5, B6, B8, B19

PC1.5 and PC2 are power classes 1.5 and 2; support depends on carrier. DL means downlink only.

## Get help

Support is available 24 hours a day at [support.dejero.com](https://support.dejero.com), [support@dejero.com](mailto:support@dejero.com), or by phone, ext. 2: 1 866 808 3665 (US and Canada) or +1 519 772 4824 (international). Every TITAN includes one year of standard support and three years of hardware support.

More guides: [TITAN Command Quick Start](/faq/titan-command-quick-start-guide/) · [TITAN Mobile Quick Start](/faq/titan-mobile-quick-start-guide/) · [TITAN Mobile User Guide](/faq/titan-mobile-user-guide/) · [TITAN Scout User Guide](/faq/titan-scout-quick-start-guide/) · [TITAN Ghost Getting Started](/faq/titan-ghost-getting-started-guide/) · [Dejero Control](/faq/dejero-control-user-guide/) · [All user guides](/user-guides/)

### Revision history

| Rev | Date | Change |
| --- | --- | --- |
| 001 | December 2025 | Initial release |
