Get TITAN Mobile mounted, powered and online. For safety notes, every port, the DIO pinout and full specifications, see the TITAN Mobile User Guide.
Watch: TITAN Mobile overview. Step-by-step training videos are coming soon.
From box to online in six steps
- Install the antennas
- Insert SIM cards
- Mount the device
- Wire the power
- Connect WAN and LAN
- Configure in Dejero Control
What’s in the box
- TITAN Mobile device
- DC power input connector
- DIO connector
- Mounting bracket
- 4 × M4 × 6 mm screws
- QR code for this guide
You’ll also need: twelve cellular antennas (SMA), two Wi-Fi antennas (RP-SMA), one GPS/GNSS antenna (SMA), 4 × M6 screws to fix the bracket, and nano SIM cards.
Install the antennas

The back panel has 12 cellular ports (5G1-1 to 5G3-4), two Wi-Fi ports and one GPS port. Choose one setup:
- Single-port antennas: one cellular antenna on each of the 12 cellular ports.
- Multi-port antennas: connect each one to a matched group: 5G1-1 to 5G1-4, 5G2-1 to 5G2-4, or 5G3-1 to 5G3-4. They only work on their matched group.
- Either way, connect two Wi-Fi antennas to the WiFi ports and one GPS/GNSS antenna to the GPS port.
Keep at least 20 cm (8 in) between cellular antennas. Tighten the SMA connector on the RF cable, not the hex lock nut on the chassis, and route cables so they reach the device without sharp bends.
Insert SIM cards
- Power off the device.
- Remove the SIM card cover.
- Insert up to three nano SIM cards (4FF; industrial-grade recommended).
- Reattach the cover.
Mount the device

- Align the mounting bracket with the installation location.
- Attach the bracket to the base of the device with the supplied M4 × 6 mm screws.
- Fix the bracket to the surface with four M6 screws, then tighten all screws.
Wire the power

- Insert the wires into the power connector and tighten the clamping screws: Pin 1 (left) V+, Pin 2 (middle) GND, Pin 3 (right) IGN, optional. Wire colours vary, so confirm before powering.
- In vehicles, fuse V+ at 10 A from the battery and IGN at 1 A.
- Plug the connector into the front of the device and tighten its screws with a flat-head screwdriver. Don’t overtighten.
- Connect the power cable to the power source.
Wire IGN only if a vehicle ignition or remote switch should turn TITAN Mobile on and off.
Connect WAN and LAN

- WAN — Port 2, or Ports 3–6: internet connections. Ports 3–6 are WAN by default and can be set to LAN.
- LAN — Port 1: your computer, switch or access point.
- Local interface: connect a monitor, keyboard and mouse to USB-C with an adapter. Reboot if the unit was already running.
- DIO (optional): fit ferrules to the wires, then press the orange plunger with a small screwdriver to insert them.
Power on
| To | Do this |
|---|---|
| Power on or off | Hold the power button at least 2 seconds |
| Reboot | Hold the power button at least 10 seconds |
| With IGN wired | On 5 seconds after ignition; off 30 minutes after ignition off (defaults) |
TITAN Mobile starts automatically when power is applied. The power LED glows green when it’s on.
Configure in Dejero Control
- Go to control.dejero.com. You need administrator permissions.
- Sign in with your email and password.
- Configure the device remotely, then connect your devices by LAN, WAN or Wi-Fi.
New to Control? Read the Dejero Control guide.
Get help
Visit support.dejero.com, email support@dejero.com, or call ext. 2, 24 hours a day: 1 866 808 3665 (US and Canada) or +1 519 772 4824 (international).
More guides: TITAN Command Quick Start · TITAN Command User Guide · TITAN Mobile User Guide · TITAN Scout User Guide · TITAN Ghost Getting Started · Dejero Control · All user guides