TITAN Scout is portable triple 5G with a built-in touch screen, carried in its own backpack. Charge it, start it, pack it and go.
Watch: why Dejero. A TITAN Scout walkthrough is coming soon.
Warranty: don’t open the device or remove the antenna endcaps on either end — doing so voids the warranty. For service, contact Dejero Support or an authorized service partner.
From box to live in five steps
What’s in the box
- TITAN Scout M4E6
- Power adapter with country-specific cord
- TITAN Scout backpack, with a power cable for a battery D-Tap port or the included V-Mount battery plates, and a weather cover
Charge it
From a power outlet
- Connect the power cord to the included adapter. Use only the adapter that ships with Scout.
- Plug the cord into DC IN on the side of Scout.
- Plug the other end into a power outlet.
From a V-Mount or D-Tap battery
- Connect the included power cord to DC IN on the side of Scout.
- Connect the cord directly to a battery’s D-Tap port, or to the V-Mount battery plate and slide a battery onto the plate.
An external battery both powers Scout and recharges its internal battery, so it drains faster.
Start it
| To | Hold the power button |
|---|---|
| Power on | 2 seconds |
| Power off | At least 2 seconds, or use Power off on the touch screen |
| Reboot | At least 10 seconds, or use Reboot on the touch screen |
Start-up messages appear on the touch screen while Scout connects.
Connect your gear
Ports on both sides carry video and audio, Ethernet, IFB and intercom. One side has the Ethernet block on the SIM module; the other has USB, Ethernet, HDMI out and DC IN.
- Port 1 — LAN: your cameras, laptops, switches or access points.
- Ports 2–6 — WAN: extra internet links for the blend. Ports 3–6 can be switched to LAN in Dejero Control.
- Built-in Wi-Fi can also act as a hotspot for phones, tablets and laptops.
Read the touch screen
- Home: blended upload and download throughput, the device serial number and software version, and the status of every WAN, cellular and Wi-Fi connection. The header shows blended tunnel status and battery level.
- Settings: brightness (auto or manual) and active SIM (primary or secondary).
- Power: reboot or power off.
The touch screen works in landscape mode in the current software. Portrait mode is coming in a later release.
Pack it in the backpack
Keep cables unbent and free of strain. Lift them clear when swapping batteries, and avoid oversized batteries that press on them.
- Fully open the top compartment with its four zippers.
- Attach any Ethernet cables to the side ports.
- Set Scout on the foam base, screen facing out and DC input facing down, with cables in the channel.
- Wrap the zip cords around the antenna endcaps, with the foam spacer between them.
- Using a battery? Check that the D-Tap connector is on the plate and the plate is held by its hook-and-loop fasteners, slide the battery on, then connect the power cable to DC IN.
- Close the top. The power cable stays in its channel, and the top foam rests on the unit, not the cables.
Always secure Scout with the zip cords so it can’t shift or fall out of the backpack.
Swap the SIM module
The removable module takes nano SIMs, so you can switch to cards for another region.
- Power off Scout.
- Loosen the thumbscrews and pull out the SIM module.
- Insert each SIM notch-first and push gently until it clicks. A card inserted the wrong way won’t go all the way in.
- To remove a SIM, push it in gently and it springs out.
- Reinsert the module with the end marked TOP toward the screen, then tighten the thumbscrews. Never force it; if it resists, take it out and check its orientation.
Get help
Visit support.dejero.com, email support@dejero.com, or call ext. 2: 1 866 808 3665 (US and Canada) or +1 519 772 4824 (international).
More guides: TITAN Command Quick Start · TITAN Command User Guide · TITAN Mobile Quick Start · TITAN Mobile User Guide · TITAN Ghost Getting Started · Dejero Control · All user guides