EnGo 260 & Backpack

The EnGo Backpack Edition Two provides fast and easy access to the EnGo 260.

Hook-and-loop fasteners are used to open the front access panel for access to the EnGo 260. It has a built-in sun shade and a compartment for cable storage.

1. Cable storage compartment
2. Built-in sun shade
3. Top compartment
4. EnGo
5. Auxiliary battery compartment
6. Expandable storage

The Edition One backpack has one zipper used to open entire top compartment for access to the EnGo. It also has a side strap for cables.

*For more information on the Edition One Backpack, please reference your User Guide or QSG

When the EnGo is inside the backpack, ensure that the cables are not bent and the connections are not under stress.

1. Use the two zippers at the top of the backpack to open the top compartment fully.
2. Connect the SDI cable to the correct input port on the side of the EnGo. For more information on using an HDMI cable with the EnGo, see "Use an HDMI cable with the EnGo Backpack Edition Two".
3. If necessary, connect the IFB audio cable to the IFB output port.
4. Set the EnGo inside the top compartment of the backpack with the screen facing out and the video and IFB ports facing down. Ensure that the EnGo sits down fully on the foam base.
5. To secure the EnGo, wrap the zip cords around the antenna endcaps at either end of the EnGo, ensuring that the foam spacer is in between.
6. Close the top of the backpack.

You must secure the EnGo in the backpack with the zip cords. If you do not, the EnGo can move around or fall out.

If you want to power the EnGo using an auxiliary battery, use the included power cord to connect to a D-Tap port on an auxiliary battery or the V-Mount or Gold Mount battery plates to charge the EnGo :

1. Run the power cable from the battery compartment up through the foam channel into the top compartment of the backpack
2. In the battery compartment, connect the D-Tap connector to the battery plate
3. Ensure that the battery plate is held in place with self-fasteners
4. Slide the auxiliary battery onto the battery plate
5. Connect the power cable to the DC IN port on the EnGO

When you connect an auxiliary battery to the EnGo the battery both powers and charges the EnGo (if the internal battery needs charging).

When the EnGo is inside the backpack, you do not need to remove it to view the screen or interact with it.

When using the EnGo outdoors, you can use the sun shade to make viewing the screen easier.

1. Open the cable storage compartment. 
2. Remove the ends of the IFB and SDI cables from the compartment.
3. Connect these cables to the external cables that you use to connect to your external camera or IFB system feeds. The external camera and IFB cables are not provided with the backpack.
4. Ensure that the IFB and SDI connections lay inside the cable storage compartment and then close the compartment. 
5. Close the top of the backpack.
6. To view the EnGo with the sun shade, perform the following actions: 
   1. Lift the front access panel from the bottom. 
   2. Unfold the triangle flaps from behind the panel. 
   3. Press the edges of the triangle flaps down on to the hook-and-loop fasteners on the sides of the front access panel.
      
      1 - Sun shade
      2 - Triangle flap
      3 - Front access panel
      4 - Self-fasteners
      
      

To view the EnGo screen without the sun shade, perform the following actions:
 

1. Lift the front access panel from the bottom. 
2. Open the triangle flaps from the inside of the sun shade to the outside and press them flat. 
3. Roll the sun shade up toward the cable storage compartment. 
4. Secure the sun shade to the hook-and-loop fastener strip on top of the cable storage compartment. Ensure that the triangle flaps are captured underneath.
   
   1 - Front flap
   2 - Self-fasteners
   3 - Front access panel
   
   

To disassemble the sun shade, lift the hook-and-loop fasteners from the triangle flaps. Fold the flaps up and close the front access panel.

By default, the backpack comes with the SDI cable already inserted. You can remove this cable if you want to use an HDMI cable instead.

If you only need to use an HDMI cable temporarily, feed the HDMI cable through the hook-and-loop fastener opening on the side of the backpack. Remove the zip cords from around the EnGo. Lift the EnGo and connect the HDMI cable to it. Replace the zip cords to secure the EnGo.

1. Use the two zippers at the top of the backpack to open the top compartment fully. 
2. If the EnGo is in the backpack, remove it.
3. At the top of the backpack, use the zipper to open the cable storage compartment. 
4. Use the hook-and-loop fasteners to open the slot in the bottom of the cable storage compartment.
   
   
   1 - Cable storage compartment
   2 - Foam spacer
   
   
5. Pull the SDI cable into the backpack through the slot in the cable storage compartment.
6. Gently separate the foam spacer from the back of the backpack and pull it forward.
7. Pull the SDI cable through the channel in the foam spacer and remove it from the backpack.
8. Route the HDMI cable behind the foam spacer, ensuring that the end of the cable that connects to the EnGo fits under the notch at the bottom of the foam spacer.
9. Ensure that the HDMI cable, as well as the IFB and power cables, fit inside the channel in the foam spacer. 
10. Align the hook-and-loop fasteners on the foam spacer with the back of the backpack, ensuring that the bottom of the foam spacer is fully inserted into the bottom of the compartment.
11. Press the foam spacer against the back of the backpack.
12. Route the HDMI cable through the slot in the cable storage compartment, ensuring that it fits into the top compartment in the same way that the SDI cable did. 
13. Use the hook-and-loop fasteners to close the slot in the cable storage compartment tightly.
14. Close the cable storage compartment. 
15. Reinsert the EnGo into the backpack, ensuring that the zip cords fit around the endcaps to secure it in place.

The EnGo 260 is the world’s most durable and versatile mobile transmitter that’s purpose-built for reliably sending high-quality live video from remote locations.

1. Antenna endcap
2. Preview screen
3. Power button
4. Antenna endcap

1. IFB Out
2. SDI In
3. HDMI In

1. USB
2. Ethernet
3. Mini DP Out
4. DC In

Additional parts included with your EnGo 260:

• Power adapter with country-specific cord
• Power cable that connects directly to a D-Tap port on a battery or the included V-Mount or Gold Mount battery plates
• A rain cover for weather protection
• Right angle SDI cable
• Right angle HDMI cable
• Mini-XLR to XLR or 3.5mm audio adapter for IFB

Do not remove the antenna endcaps -- removing them voids the warranty. To service the EnGo 260, contact Dejero support or your Dejero-authorized service partner

You can use the connection ports on either side of the EnGo to connect video and audio, Ethernet, or IFB. You can also use the USB ports on the EnGo to connect a keyboard or mouse, or a Logitech H390 USB headset when using the Intercom feature.

When you receive your Edition Two backpack, the IFB and SDI cables are already inserted

Use only the charger that is included with the EnGo 260.

1. Connect the power cord to its power adapter
2. Connect the power cord to the DC IN port on the side of the EnGo
3. Plug the power cord into a power outlet

If you want to power the EnGo using an auxiliary battery, use the included power cord to connect to a D-Tap port on an auxiliary battery or the V-Mount or Gold Mount battery plates to charge the EnGo :

1. Run the power cable from the battery compartment up through the foam channel into the top compartment of the backpack
2. In the battery compartment, connect the D-Tap connector to the battery plate
3. Ensure that the battery plate is held in place with self-fasteners
4. Slide the auxiliary battery onto the battery plate
5. Connect the power cable to the DC IN port on the EnGO

When you connect an auxiliary battery to the EnGo the battery both powers and charges the EnGo (if the internal battery needs charging).

On the front of the EnGo, press and hold the power button

1. Power button

When the EnGo 260 is on, the Preview screen appears

1. Power source
2. Network connections
3. Menu
4. Go Live button
5. Status
6. Record Button
7. Status
8. Record Menu
9. Live Menu

You can use the Preview screen in portrait or landscape mode.

The touch screen on the EnGo 260 is a capacitive screen. If you are wearing gloves, you must remove them before using the screen